Registering for Devil Mountain Double 2013

A week ago I mailed my check and entry form for the Devil Mountain Double. I ask myself: what have I done?

2000
riding Patterson Pass in 2000

The first time I did this ride in 2000 (ride report). That year I froze on the Diablo descent, bonked on San Antonio Valley Road, was saved by a cup of soup at Crothers, recovered remarkably, then managed to grind out Sierra Road, Calavera, Palomares, Crow Canyon, and finally Norris Canyon to finish. Just finishing was enough.

The second time I went in with a bit too much confidence and rode strongly to the base of Mines Road, where I was suffering badly. Low on energy and deterred by reports of hail from the summit of Mount Hamilton up ahead, I turned back, finishing the day with 150 miles with major climbing but with only a DNF to show for it.

That was 2002.... a long, long time ago.

Every year I note its approach. Every year I know I must return: to get it right, to prove I can ride smartly, finish strongly. Time really doesn't matter. What matters is riding every hill as strongly as the others. To go out at a pace I can sustain. To drink on a regular schedule, calories on a regular schedule, and electrolytes on a regular schedule to avoid the need for intravenous soup like the first time.

I'll start with the second group, because my last two doubles say I deserve to. But I fully expect to fall well off the pace of that group when the fireworks begin on the lower slopes of South Gate Road. The time to rage, if any, is Norris Canyon, maybe Palomares. But I have no plans for raging after more than 16 thousand feet of climbing in my legs by that point. This is about surviving intact, with minimal idle time, finishing hopefully in daylight but that not being the focus.

The Devil Mountain Double is a ride which demands enormous respect, fear really. Go too hard, and there will be a terrible price to be paid in the end, assuming optimistically I make it to the end. But go too slowly and, well, I'll be slow. Steady: that's the key.

But back to the original question: why? I don't look forward to the ride. It will hurt. I will feel despair. It will leave me broken, requiring at least a week before I feel moderately good again, two weeks before I feel fresh. There's other things I could be doing with my time. But it will feel so very, very good to finish, if I do. That's the addictive part.

Comments

Post a Comment

Popular posts from this blog

Marin Avenue (Berkeley)

Image
On Saturday, I got an email from Tim telling letting me know that Murphy's Spring Classics was going to start up Marin Ave. I'd missed that. Murphy announces his courses the day before, and indeed it was already well into the night before when the course announcement went out. I'd skipped over the details, jumping straight to middle and end games. Marin? I laughed at the irony, because not long before when he'd told me he was choosing to repeat the Nifty Twn Fifty which we'd done together last year versus selecting Murphy Mack's Stage Mullett two-day, I responded I didn't think I had it in me to ride Marin Ave two years in succession. Well, so much for that. I was committed, so I went downstairs to swap my 11-26 cassette for my Recon 12-27. The name is easily overlooked: "Marin Ave" fails to strike the same impression as, for example, "Redwood Gulch" or "China Grade". But among those in the know, Marin Ave is infamous i
Read more

hummingbird feeder physics

Image
I couldn't figure out how the hummingbird feeder worked. Why didn't it overflow? Forces need to balance, of course. Neglecting surface tension, there liquid level is higher in the inner reservoir than in the feeding chamber, so there must be a corresponding pressure difference. Suppose the pressure in the inner chamber were zero. Then the column height difference would need to be atmospheric pressure / (density of liquid × gravity). But this is over 9 meters! Obviously the height difference is only approximately 1% of this. So the pressure difference inside versus outside is only approximately 1%. The inside is only slightly below atmosphere. So air is getting in. How? Does it diffuse through the liquid? If this were the dominant mechanism, it wouldn't take long for the pressure inside to go from 99% to 99.3%, for example, which should be plenty to push the column of liquid down in the inside chamber and thus push liquid out through the holes. It would over
Read more

Gallium Pro geometry

Image
On Caltrain yesterday, I was surprised to see among the usual set of commuting bikes a SRAM Red-equipped Argon Gallium Pro. The bike immediately stole your attention. The design was one which has been trending: clear-coated carbon with plenty of text detail so the viewer is sure to realize he's gazing upon the result of advanced, proprietary engineering and not at yet another paint job on the same old OEM frames being pumped out of the same old Taiwanese factories. But it worked: the bottom bracket area was huge, the downtube a large-diameter "inverted Kamm tail" design seemingly designed to maximize wind resistance, the top tube a broad, eccentric shape which screamed "vertically compliant yet torsionally stiff". All it lacked were the pencil-think seat stays Cervelo popularized, but this was a machine designed for stiffness over anything else. It seemed dramatic overkill, since the bike was small (the Argon "XS" I suspect). There wasn't muc
Read more